DIY 15KV High Voltage Inverter Generator Spark Arc Ignition Coil Module 3.7V Kit for Sale

Recent Threads

On eBay Now...

DIY 15KV High Voltage Inverter Generator Spark Arc Ignition Coil Module 3.7V Kit For Sale

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

DIY 15KV High Voltage Inverter Generator Spark Arc Ignition Coil Module 3.7V Kit:
$3.37

Note: This item is DIY Kit, not assembled. default with one PCB board.
Features:◦This product is a booster coil production suite, the circuit is simple and reliable, with a professional line drawings, electronic research convenience enthusiasts
◦Uses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high frequency arc, high temperature, can easily ignite combustible materials, so it was called the plasma lighters
Parameter:◦15KV transformer outside dimensions of approximately: 27×16×21mm◦Input voltage: DC 3.7V-4.2V (limit 12v, easy to damage not recommended, this transformer is equally applicable to 12V input voltage, but requires a corresponding increase in the base of the response resistor to about 150Ω ~ 1.5KΩ, its resistance should be large to replace a small adjustment, or burned transistor or transformer)◦Input Current: <2A◦Output voltage: approximately 15KV (please pay attention to safety when used)◦Output Current: ≤0.4A◦High voltage bipolar ignition distance: ≤0.5 cm
◦When the product input termination 3.7V-4.2V power supply, the secondary high voltage output is not connected to high-voltage rectifier diodes and capacitors, output terminals levels ≤1.5cm long can produce purple high temperature arc, no crackling, but the temperature is very high , you can easily and instantly point cigarette paper, or even very thin wire burned Sparks (such as junior high school chemistry experiment thin wire in oxygen combustion scene, but not as good as oxygen so intense.)
Transformer structure:There are two primary windings, a primary winding, a response winding, the secondary output of high pressure. Other: 15KV transformer designed for maximum output, limit output can not exceed 15KV, is one centimeter arc, a higher output voltage is likely to damage the transformer.
PCB board size: 4.2CM * 3.2CM * 0.16CM;
Installation Notes:1). With the PCB board parts better production, in which the transformer line of thick line and thin line, this should pay attention to the other components by the board of silk symbols and parameters of welding on the line. Transformer board has done three pads, in which the middle of the pad hole is relatively large, the hole at the same time welding a thick enameled wire and a thin enameled wire, thick enameled wire and fine enameled wire do not use the same side, such as with the left Thick lines and the right side of the thin wire into or with the left side of the thin line and the right side of the thick line welding into, in short, do not use the same side of the thick lines and thin lines can be.
2). In order to prevent the output 2-wire distance too far, resulting in no-load, you can weld a 3P pin at the output.
3). After the success of the production, if the output access to a high-voltage capacitor and three high-voltage rectifier composed of voltage doubler circuit, you can produce DC high voltage, you can make anion generator, wiring diagram is as follows:

Package Include:15VKE = 1 type step-up transformer x1PCB Board X 1120 ohm resistance X 1UF4007 ultra-fast recovery diode X 1N20 transistor X 1Heat sink X 1M3 * 6 screws X 1Boat switch X 13-Pin X 1

Note:
1. Some pictures look bigger, please refer to the exact item size.
2. Please note that due to lighting effects, monitor's brightness and contrast settings, the color of the products may vary slightly between our photos and the item actually received.
3. We thank you for your understanding.

We accept PayPal only.

We only ship item to your PayPal verified address.

Please make payment asap, then we can arrange shipment for you asap.

We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost.

Delivery time depends on destination and other factors.

Any questions,please contact us via message, In our working hours will be resumed within 48 hours.
If you are satisfied with our service, please kindly leave us a positive response and give us the Detailed Seller Rating with all "5 stars" in very area.
Our aim is to provide Top Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy. We greatly appreciate your POSITIVE response.Please do NOT leave negative response without asking for help. Thanks!

Contact us through message.
We will always do our up most to exceed your expectations in customer service, communication and dispatching of your orders.