0~55MHz DDS Signal Generator*Direct Digital Synthesis HAM Radio VFO Wireless for Sale

Recent Threads

On eBay Now...

0~55MHz DDS Signal Generator*Direct Digital Synthesis HAM Radio VFO Wireless For Sale

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

0~55MHz DDS Signal Generator*Direct Digital Synthesis HAM Radio VFO Wireless:
$31.31

Free USPS First Class Shipping.

Features :
This is a 0~55MHz DDS Signal Generator. It is based on AD9850 chip and is very easy to operate.

Supports 0~55MHz continual adjust at 1Hz step.

This generator has 78L05 voltage regulate. Input current at 200MA, input voltage 8-9V would be the ideal voltage.

Input voltage of 12V can only be used for short time testing, otherwise will cause heat to board.

5p/6p connect to encoder as per photo. 7p of the middle connects to digital matrix input. 14p (8V GND) is 8V power supply from main board. If powered by main board, DDS does not need independent power supply.

1~6 correspond to 6 frequency bands: (3.8，7 ，9，14，18 or 21，27 or 29)

ISB, USB, CW are the three mode choices.

DT is signal from main board.

Keys & Connection interfaces:

ENC: encoder switch
MEM: switch for memory mode
VFO: Transfer from VFO A to VFO B, or from VFO B to VFO A.
SSB: Working mode change: circulate from USB, LSB, AM, CW, and on and on...
RIT: fine tuning to receiving frequency
CAL: set functions
KB-1 and KB-2 have common shared pin, but is not GND.

How to operate:

Press CAL, power on, then we enter setting screen. Let go/release CAL.

A: ENABLE 6XREFCLE: setting chip clock mode, adjust frequency encoding setting. AD9851 set to 6-multiply frequency, AD9850 set to 1multiply frequency. Press CAL then quickly release to enter next step B.

B: DDS-SYSTEM-CLK: Chip working frequency setting. Use encoder switch to adjust value. Operate in accordance with STEP key. AD9851 set at oscillator 6-multiply channel, AD9850 set at actual output of oscillator. Press CAL then quickly release to enter step C.

C: MIN_RX_DDS_FREQ：Setting minimum working frequency. Use encoder switch to adjust value and in accordance with STEP key. Press CAL then quickly release to enter step D.

D: MAX_RX_DDS_FREQ：Setting maximum working frequency. Use encoder switch to adjust value and in accordance with STEP key. (Smaller than 60MHz would be OK ). Press CAL then quickly release to enter step E.

E: SSB_OFFSET：Fine tuning for SSB working mode. Use encoder switch to adjust value and in accordance with STEP key. Press CAL then quickly release to enter step F.

F: CW_OFFSET：Fine tuning for CW working mode. Use encoder switch to adjust value and in accordance with STEP key. Press CAL then quickly release to enter step G.

G: OFFSET_FREQ：Setting of offset Frequency. e.g, set to 9MHz or 10.7MHz, use encoder switch to adjust value and in accordance with STEP key. Press CAL then quickly release to enter step H.

H: MULTIPLIER: multiply setting for frequency. Should be set as 1, press CAL then quickly release to enter step I:

I: Screen displayes word "SAVE", automatically save the above setting, and returns to normal working.

Notes:

1. DDS SYSTEM CLK: can use frequency tester to get 30MHz oscillator, multiply the tested value at 6, then put the multiplied value here. If using AD9851, make initial setting at 180000000.

2. OFFSET FREQ: can be set as + or - . Rotate encoder switch to change value, press STEP key, then rotate encoder switch to adjust step. Minimum working frequency plus (+) offset frequency should be high than 0 (zero).

Frequency display:

RX = MULTIPLIER x (RX_DDS_FREQ + OFFSET_FREQ)

TX = MULTIPLIER x (RX_DDS_FREQ + OFFSET_FREQ + TX_OFFSET_FREQ)

The frequency programmed into the DDS, is calculated as shown below.

RX = ABS(RX_DDS_FREQ)

TX = ABS(RX_DDS_FREQ + TX_OFFSET_FREQ)

RX_DDS_FREQ, MIN_RX_DDS_FREQ, MAX_RX_DDS_FREQ, TX_OFFSET_FREQ & OFFSET_FREQ

Examples:

1. DDS output range 30~40MHz:

MIN_RX_DDS_FREQ MAX_RX_DDS_FREQ OFFSET_FREQ RX Frequency display range.

30 MHZ 40 MHz 100 MHz = 130 MHz to 140 MHz. \ Note 1

30 MHZ 40 MHz -10 MHz = 20 MHz to 30 MHz. /

-40 MHZ -30 MHz 170 MHz = 140 MHz to 130 MHz. \ Note 2

-40 MHZ -30 MHz 60 MHz = 30 MHz to 20 MHz. /

2. setting FT180A with DDS:

ENABLE RPT NO

X6 RECLK X6

DDS SYSTEM CLK 180M

MAX DDS FREQ 65M

MIN RX DDS FREQ 10.701M (Offset frequency + RIT frequency)

MAX RX DDS FREQ 60M

TX OFFSET FREQ 0

MAX RIT OFFSET 1K (RIT frequency)

OFFSET FREQ －10.700M －(Offset frequency)

MULTIPLIER 1

Package：
100% Brand New
1 x 0~55MHz DDS Signal Generator * Direct Digital Synthesis HAM Radio VFO Wireless

Payment

1. We accept PAYPAL only.
2. Payment must be made within 7 days of sale closing (Unpaid dispute will automatically open when item
is not paid in 7 days).
3. PLEASE NOTE: SHIPPING&HANDING DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES.
4. Please list your special requests (color, packages, value of declaration, etc.) in the NOTES SECTION
when you make payment

We offer USPS First Class Shipping / Not Ecomomy

- There is a big difference between USPS First Class Shipping and Economy Shipping

-Our orders are shipped every day and delivered within 3-8 days

Returns Policy

1. Customer satisfaction is our top goal. All products are quality checked. They are new and in good condition when shipped to our customers. If product is defective or damage upon arrival, or wrong product shipped, please keep in touch with us immediately. Returns accepted within 14 days of delivery date
and item must be in original new condition, not worn or altered in any way with attached tags & wrap.Otherwise deal is final. Return shipping must be paid by buyer.
2. Please keep in touch with us first if you have anyproblems/questions/concerns. We will be happy to resolve
any issues you may have in a cordial and friendly manner.
3. We appreciate your Positive response, and will do the same in return. PLEASE DO NOT leave negative response without first communication with us. Please allow max 24 HOURS for us to respond

About response

We maintain high standards of excellence and strive for 100% customer satisfaction! response isvery important to us. We request that you keep in touch with us immediately BEFORE you give us neutral ornegative response, so that we can satisfactorily address your concerns.It is impossible to addressissues if we do not know about them!